Woodcutting Tutorial – RM2K3

This will soon be updated and migrated to the Tutorials & How-To's section.
Woodcutting Demo
The link to the demo
is no longer available here.

This is how to create a basic woodcutting process in RM2K3, similar to that used in Runescape, but without the experience points gained.

Using the “defaults” from a new Project, first create two common items: Handaxe and Logs.

Also, create a variable to store the number of logs chopped. In this example, 0001:Wood.

Next, create a map and place a few events on it, setting the event graphics to trees. Make sure you name each one differently, as each one also has a matching switch. For this tutorial, I created 4 “tree events”, named Tree1, Tree2, Tree3 and Tree4.

Create another event for the Woodcutter, who will give you an axe with which to chop the trees down. In the Woodcutter’s Event Commands, we’ll need to set it up so that:

  • He first checks to see if you have a Handaxe. If not, he’ll give you one. If so, he’ll tell you how many logs you’ve chopped.
  • If you’ve collected the required number of logs (in this case 10), he’ll congratulate you. If not, continue until you have the number of logs.

The code for this is as follows:

Branch if Handaxe Possessed
Branch if Var[0001:Wood] is 10
Message: Congratulations! You've collected 10 logs.

: Else Handler
Message: You've collected V[1] out of 10 logs.

: End

: Else Handler
Message: You don't have an axe! Here, have this one!
Change Items: Handaxe 1 Add

: End

The next step is to set up the trees so that they can be chopped down and you’ll receive some logs. We’ll start with the “Tree1” event.

Create 2 pages. In the Event Commands (Page 1), we need to:

  • Check once more if you have a Handaxe – you can’t chop trees down with your bare hands, after all.
  • If not, display an appropriate message.
  • If so, change the tree to a stump and add the logs to the inventory, not forgetting to “store” the number of logs possessed.
  • Finally, add some sound effects and chop away!

Branch if Handaxe Possessed
Play Sound: Axe Swing
Wait 1.0 Sec
Play Sound: Axe Swing
Wait 1.0 Sec
Play Sound: Axe Swing
Wait 1.0 Sec
Play Sound: Tree Falling
Switch Operation: [0001:Tree1] ON
Message: You received some logs.
Change Items: Logs 1 Add
Variable Oper: [0001:Wood] + , 1

: Else Handler
Message: You'll need a handaxe to chop this tree.

: End

On Page 2, set the first switch under “Preconditions” to 0001:Tree1 and the “Event Graphic” to that of a tree stump.

Repeat the steps for the other tree events, changing the name of the switch to match the name of the event, i.e. in event Tree2 the switch name would be Tree2, and so on.

Now, of course, since we only created four trees, but need 10 logs for the tutorial, the trees would need to regrow. For this, we need to create a simple variable-based timer. Set the “Trigger Condition” (on Page 2) to “Parallel Process”. In the Event Commands, place the following:

Variable Oper: [0002:Seconds] Set , 0
Wait 5.0 Sec
Variable Oper:[0002:Seconds] + , 1
Branch if Var [0002:Seconds is 5
Switch Operation: [000:Tree1] OFF

: Else Handler
Jump to Label:1
: End

Repeat for the other Tree events, once again changing the Switch Operation to the corresponding event name.

When you’ve collected 10 logs, speak to the Woodcutter and demo over.

2 thoughts on“Woodcutting Tutorial – RM2K3

  1. Thanks! You might be onto something there! Good idea! And, of course, as in RS, different types of trees produce different types of logs, regenerating at different rates! Might have to look into expanding this tut for a future project. =)